A Consistent Methodology for Forensic Photogrammetry Scanning of Human Remains Using a Single Handheld DSLR Camera

A Consistent Methodology for Forensic Photogrammetry Scanning of Human Remains Using a Single Handheld DSLR Camera

Ujvári, Zsolt

Metzger, Máté

Gárdonyi, Gergely

postmortem documentation

3D documentation

photogrammetry

optical surface scanning

cloud-to-mesh comparison

Társadalomtudományok

Társadalomtudományok/Rendészet tudományok

Due to increasingly capable algorithms and more available processing power, photogrammetry is becoming a simple, cheap and accurate alternative to 3D optical surface scanning. With adequate application, it can be a swift documentation technique for reconstructing the geometry and body surface of deceased persons in autopsies, or other forensic medical examinations. Sufficiently easy and swift 3D documentation techniques may allow 3D imaging technologies to become part of the daily routine of any forensic medical examiner or other medical personnel. This paper presents a consistent and systematic photographing methodology (as an alternative to automated or intuitive methods) for photogrammetry scanning of human remains. Although it requires manual photography, the methods presented in this paper offer a swift and easy way to capture an accurate 3D model of human remains under almost any conditions. Four different photographing procedures were tested on four subjects: ([DiMaio D, DiMaio VJM. Forensic Pathology: Practical Aspects of Criminal and Forensic Investigations, second ed. Boca Raton (FL): CRC Press, 2001.]) a systematic circular technique with 100 photos, ([Prahlow JA. Forensic Pathology for Police, Death Investigators, Attorneys, and Forensic Scientists. New York (NY): Springer, 2010.]) a systematic circular technique with 50 photos, ([Shkrum MJ, Ramsay DA. Forensic Pathology of Trauma: Forensic Science and Medicine. Totova (NJ): Humana Press, 2006.]) a technique loosely mimicking cameras mounted on a postmortem CT device with 98 photos, and ([Urbanová P, Hejna P, Jurda M. Testing photogrammetry-based techniques for three-dimensional surface documentation in forensic pathology. Forensic Sci Int 2015,250:77–86.]) a technique mimicking cameras mounted on a postmortem CT device with 49 photos. Measurement accuracy was tested with the aid of six adhesive control points placed at approximately the same locations on each subject. Five different distances defined by these control points were measured and compared to the measurements taken by hand. 3D photogrammetry meshes created using these techniques were also compared with point clouds acquired using a 3D laser scanner. We found that a carefully composed, tested, and systematic photographing procedure significantly improved the quality of the photogrammetry models. In terms of relative difference compared to the hand measurements, both technique 1 and technique 2 produced close results, with an average relative difference of 0.160% and 0.197% and a maximum relative difference of 0.418% and 0.481% respectively, while models reconstructed from images taken using technique 3 and technique 4 seemed to be much less accurate, with an average relative difference of 0.398% and 0.391% and a maximums relative difference as high as 1.233% and 1.139% respectively.

info:eu-repo/semantics/other

application/pdf

nke:2471-1411

nke:2096-1790

http://hdl.handle.net/20.500.12944/24905

nke:10.1093/fsr/owad036

nke:10.1093/fsr/owad036

nke:34171856

nke:10087072

nke:Forensic Sciences Research

nke:Forensic Sciences Research

nke:8

nke:4

nke:001155616500001

nke:85186181395

nke:FORENSIC SCI RES

LOMS: https://tudasportal.uni-nke.hu/xmlui/bitstream/20.500.12944/24905/1/A%20consistent%20methodology%20...

info:eu-repo/semantics/openAccess